mono 螺耐斯环保

定转子过早磨损Premature wear of fixed rotor定转子过早磨损主要是由于定转子的间隙过小引起的。The premature wear of the fixed rotor is mainly caused by the small gap between the fixed rotor and the rotor.油管与抽油杆柱磨损Oil pipe and rod string wear油管与抽油杆柱磨损的原因一是因为井斜抽油杆贴在油管壁上引起的，可以通过加抽油杆扶正器使抽油杆柱居中来减轻或消除，另一个原因是定转子不同心及转子的偏心运动造成的，在定子以上加一节内径较大的回转筒即可避免。Tubing and sucker rod wear reason is because the deviation of sucker rod attached to the tubing wall caused by heating， pumping rod centralizer make the rod center to reduce or eliminate， another reason is caused by the eccentric motion of the rotor and the rotor are not concentric， avoid a day the diameter of rotary cylinder in the stator can be larger than.

单螺杆泵工作时，两端分别作用着液体的吸排压力，因此对螺杆要产生轴向推力。螺杆泵厂家建议对于压差小于10千克力/cm2的小型泵，可以采用止推轴承。此外，mono，还通过主动螺杆的中央油孔将高压油引入各螺杆轴套的底部，从而在螺杆下端产生一个与轴向推力方向相反的平衡推力。

　　单螺杆泵和其它容积泵一样，当泵的排出口完全封闭时，泵内的压力就会上升到使泵损坏或使电动机过载的危险程度。所以，螺杆泵厂家建议使用时在泵的吸排口处，就必须设置安全阀。

Ｅ、抽油杆扶正器E， sucker rod centralizer抽油杆扶正器由心轴和扶正筒组成，它接在两根抽油杆之间，被卡在两个抽油杆接箍之间。心轴也就是一要极短的抽油杆短节。扶正筒是一个内孔比心轴大１ＭＭ左右的空心塑料筒，外部有四个略比油管内径小的扶正翼，采取浇注成型。扶正筒可以围绕心轴转动，防止抽油杆旋转时与内壁接触而磨蚀油管，又可以让流体通过。The sucker rod centralizer is comed of the heart shaft and the upright cylinder， which is connected between the two sucker rods and is stuck between the two sucker rod hoops. The axis of the heart is also an extremely short rod short section. The centering cylinder is a hollow stic tube inner hole Bixin shaft around 1MM， external four slightly smaller than the diameter of the tubing centralizer wing， adopt casting. The centralizer can revolve around the axis to prevent the sucker rod from touching the inner wall when it rotates， and it can also let the fluid pass through.



mono-螺耐斯环保(在线咨询)由武汉螺耐斯环保设备有限公司提供。武汉螺耐斯环保设备有限公司是一家从事“螺杆泵,单螺杆泵,螺杆阀,污泥切割机,污泥破碎机,微型螺杆泵”的公司。自成立以来，我们坚持以“诚信为本，稳健经营”的方针，勇于参与市场的良性竞争，使“螺耐斯”品牌拥有良好口碑。我们坚持“服务至上，用户至上”的原则，使螺耐斯在污水处理设备中赢得了客户的信任，树立了良好的企业形象。 特别说明：本信息的图片和资料仅供参考，欢迎联系我们索取准确的资料，谢谢！

---